|
Factorite (Elite) Posts: | 187 |
Location: | Herts. UK | Status: | |
| Hi,
I got the above mentioned card and tryied to install it in my 900c with cmonexv1.0
1. The card seems to have an Intersil PRISM chip
2.Installed drivers, that are for WM2003 or PPC2003, depending of the source. The cab installed with the warning that "not for this machine and probably will not work properly". Well do not work.
3.The card is detected and asks for driver name, copied the long name but nothing happens!!!!
4. Somewhere suggested that a cab from Samsung called CopyDriver should be installed followed by a soft reset,. Done that and nothing!!!!!still driver not recognised.
5 Tried with PRISMNDS and ISLP2 but no success!!!
6 Has anybody used this card?
7. Any ideas?
8. ExeCheck does not recognise the installed dll's. And I can see nothing else installed, but remove programs show both cabs installed.
Cheers!!!
PS: Probably wasted 10 quid, and "to be good to be true" is valid again!!!!
PS2:Can somebody send me the Planex 54G drivers? I think is a Prism also? |
|
|
|
Global Moderator H/PC Guru Posts: | 7,188 |
Location: | USA | Status: | |
| I ordered the same card from eBay, am waiting to get it to experiement with it myself....could be I'm in the same boat as you...worthless for hpcs....
Rich |
|
|
|
H/PC Oracle Posts: | 16,175 |
Location: | Budapest, Hungary | Status: | |
| i saw those cards on ebay before for dirt cheap..
but did not buy it because i saw it wouldnt work, i forget why i thought so..
Quote 8. ExeCheck does not recognise the installed dll's. And I can see nothing else installed, but remove programs show both cabs installed.
what do you mean by it not recognizing the dlls? Edited by cmonex 2007-10-18 7:12 PM
|
|
|
|
Factorite (Elite) Posts: | 187 |
Location: | Herts. UK | Status: | |
| Hi,
I mean ExecCheck in /windows do not show anything related to Samsung, but the dll's are in /win.
Cheers |
|
|
|
H/PC Oracle Posts: | 16,175 |
Location: | Budapest, Hungary | Status: | |
| thats strange...can you copy the dlls out to root and try exechecking them there? |
|
|
|
Factorite (Elite) Posts: | 187 |
Location: | Herts. UK | Status: | |
| Hi,
I hate to waste money so:
1. Removed the installation of both cabs.
2. Reinstalled both cabs in /windows paying more attention on what was happening:
- Both cabs installed the SAME swld26c.dll
- The suposed driver also installed something called "Samsung Electro-mechanics SAMSUNG WLAN 11g CF adapter, ending with a .UNLOAD
- The CopyDriver cab installed a file called Intermec Technologies CE Toolkit.unload.
3. When I run ExecCheck on the installed swld26c.dll and the 900c freezes(tried several times) and a soft reset is requiered.
Any comments
Cheers!!! |
|
|
|
H/PC Oracle Posts: | 16,175 |
Location: | Budapest, Hungary | Status: | |
| the .unload is fine, that is for the remove apps program in control panel.
so you copied swld26c.dll out of \windows?
but anyway if the driver only consists of a dll, there is not much to hack on it really. it means it has no gui config app (relies in wzc, i'd assume), and with drivers,it is usually only the gui you need to get working..
i think (IIRC) my problem was that the pokcetpc driver didnt work even on wm2003. just ppc2002.
p.s.: if you could upload the driver cabs i'd check them out just in case..
Edited by cmonex 2007-10-19 10:41 PM
|
|
|
|
Global Moderator H/PC Guru Posts: | 7,188 |
Location: | USA | Status: | |
| Okay, here is the news...I got my Magiclan card today. Put it in, tried the first driver I found nothing. Then I downloaded and install this driver: http://members.fatalpunishers.com/Bartek/SamsungCopyDriver.CAB
Put the card in and when it asked for the driver name, entered swld26c and it lit up. I was able to connect fine to my home network, but the signal was very low.
So I then set my wireless router (Netgear ) to be in G mode only. I also took a piece of solder, about 24 inches long and connected to the center conductor of the ANT2 connector on the wifi card. The signal went from poor to very good and I was connected to my home network in G mode. And it was significantly faster in downloading web pages than previously. Still need to experiment some, but wow....this looks promising...
BTW, got the card in auction 160167705188 on eBay for $23. Take a look at it and you can see the two antenna connectors I am talking about.
Rich |
|
|
|
H/PC Oracle Posts: | 16,175 |
Location: | Budapest, Hungary | Status: | |
| hmm, the cards i was going to buy were like 5$ each a few months ago.. |
|
|
|
Global Moderator H/PC Guru Posts: | 7,188 |
Location: | USA | Status: | |
| Well gee whiz Monica, you sure didn't tell me about that $5 deal, I mean a wifi G card that works in G mode on the 900C?
Rich |
|
|
|
H/PC Oracle Posts: | 16,175 |
Location: | Budapest, Hungary | Status: | |
| yeah but i thought it wouldn't work... or not much chance. well, i've always known i can't google too well |
|
|
|
Global Moderator H/PC Guru Posts: | 7,188 |
Location: | USA | Status: | |
| Pulled the antenna off an old cardbus card and soldered it onto the MagicLan...works great. Now I don't have to hold a piece of solder for an antenna...
Still testing though...
(pic1.jpg) Attachments ---------------- pic1.jpg (30KB - 1 downloads) |
|
|
|
H/PC Elite Posts: | 672 |
Location: | (lost in) Italy | Status: | |
| Rich, wich kind of antenna did solder on it (connector type)? can you post a picture of the hardware mod?
Edited by Dan 2007-10-27 11:09 AM
|
|
|
|
H/PC Oracle Posts: | 16,175 |
Location: | Budapest, Hungary | Status: | |
| Rich: i forgot to mention, but i got a 802.11G card working too... that planex CF wifi card stingraze is selling. (hidden SSID works on the 900c.) |
|
|
|
Factorite (Elite) Posts: | 187 |
Location: | Herts. UK | Status: | |
| Hi,
No luck here!!!!
Now any time I insert the MagicLan the 900c freezes!!!
I give up. Will buy a card that does not need an ext aerial!!
Anybody interested in the MagicLan, just pay postage, email me.
Cheers |
|
|