|
| Hallo,
I have problem with battery on my MobilePro900c. Battery is full (it is cca. 8.2V on my meter ), I work with MPro about 3 hours, but MPro show without battery. Window battery propetries show 0% power and Main Batterries don´t show nothing.
Other information on pictures
Thanks Vašek |
|
|
|
| Quote vasekv - 2008-09-12 10:52 PM
Hallo,
I have problem with battery on my MobilePro900c. Battery is full (it is cca. 8.2V on my meter ), I work with MPro about 3 hours, but MPro show without battery. Window battery propetries show 0% power and Main Batterries don´t show nothing.
Other information on pictures
Thanks Vašek
Here isi address with information about my MobilePro:
http://www.prvni.estranky.cz/fotoalbum/nezarazene/mpbilepro/original/105
Vasek |
|
|
|
Global Moderator H/PC Guru Posts: | 7,188 |
Location: | USA | Status: | |
| Battery works for 3 hours...that is good. |
|
|
|
| Quote Rich Hawley - 2008-09-13 3:10 PM
Battery works for 3 hours...that is good.
Thanks, it is good, but why is indicator on my mobile is bad. And mobilePro show battery is low?
Vasek
|
|
|
|
Global Moderator H/PC Guru Posts: | 7,188 |
Location: | USA | Status: | |
| Check battery show again, use power icon in control panel, make sure a/c adapter is not plugged in when checking... |
|
|
|
Factorite (Elite) Posts: | 180 |
Location: | United Kingdom | Status: | |
| Have you tried a hard reset,( main battery & back-up battery removed)
back-up your files before doing this
Airhook |
|
|
|
| Whena I use control panel is there this information :
Main battery isn´t bold GOOD, LOW not even VERY LOW ( for example : Backup batteries is bold GOOD ) on the pictures.
When I plug A/C adapter, notice MAIN Battreri is change on CHANGING and when is batteries is charge is there EXTERNAL.
I try hard reset, but is it still same.
HW is MobilePro 900 but SW is CE NET 4.2. Maybe, it is problem?
Configuration my MobilePro is:
In window Batteries (WR-Tools ) is bad voltage 1.413 V, no consumption, no temperature
|
|
|
|
Global Moderator H/PC Guru Posts: | 7,188 |
Location: | USA | Status: | |
| Sounds like you have a bad battery. Hard to say without trying another. Just use it until it doesn't work, and then worry about it...
Rich |
|
|
|
|
It isn´t bad battery (I can work on battery about 2-3 hours).
I try plug in power supply (7.66V) instead of battery (without A/C adapter, sure).
MobilePro show me same information as before.
I think, it is some library (*.dll) or HW problem,... ?
Vašek
|
|
|
|
H/PC Elite Posts: | 672 |
Location: | (lost in) Italy | Status: | |
| Quote vasekv - 2008-09-12 10:52 PM
Hallo,
I have problem with battery on my MobilePro900c. Battery is full (it is cca. 8.2V on my meter ), I work with MPro about 3 hours, but MPro show without battery. Window battery propetries show 0% power and Main Batterries don´t show nothing.
Other information on pictures
Thanks Vašek
I had a similar problem and found the internal battery switch (controlled by the external battery switch ) had blocked in the open position (even when the external switch was in the locked position ) but I had cmonex 2 installed and think this shouldn't be possible to happen to you, as with the standard ce.net rom the device wouldn't even start up without the switch in the locked position..
Hardware problems aside, I think there is a system hack to make the warning disappear Edited by Dan 2008-09-15 2:44 AM
|
|
|
|
Global Moderator H/PC Oracle Posts: | 12,674 |
Location: | Southern California | Status: | |
| Speaking of cmonex' ROM, it probably couldn't hurt for vasekv to try reflashing the 900C with version 2. (I see it already has the right bootloader version. ) |
|
|
|
| I solved problem with battery.
Problem was with internal battery switch. This switch was all time blocked.
Thanks for yours tips.
Vasek |
|
|
|
H/PC Elite Posts: | 672 |
Location: | (lost in) Italy | Status: | |
| Quote vasekv - 2008-09-16 7:58 AM
I solved problem with battery.
Problem was with internal battery switch. This switch was all time blocked.
Thanks for yours tips.
Vasek
So, did the device start up even with the switch in the open position? |
|
|
|
|
Switch was in postion push as lock is OPEN, but I think it had bad contact.
I cleared switch with oil and function is OK. Now when I unlock switch my MPro is switch off.
Vasek |
|
|
|
H/PC Oracle Posts: | 16,175 |
Location: | Budapest, Hungary | Status: | |
| hey vasekv. I'm not sure I fully understood... is this the internal switch, did you have to disassemble the device to get to it? I assume so.. |
|
|