|
H/PC Newbie Posts: | 5 |
Location: | Afghanistan | Status: | |
| Hi i have a problem with loading of Winampaq on my Alpine PMD-B200P WinCE 4.20 ARM based navigator.
when i try to run the exe it says: Cannot find Winampaq(or ono of its components) Make sure the path and filename are correct and th all the required libraries are available.
I read around the net there is a utility called execheck but i cannot find it..
Any advice?
Thankyou |
|
|
|
H/PC Newbie Posts: | 5 |
Location: | Afghanistan | Status: | |
| UPDATE
Found execheck i miss mfcce300
i downloaded file but i dont know where put it. i try in the installation folder but doesnt work
i put it in the windows folder too but doesnt work
the message of execheck is the same. if i reboot the files in windows directory disappears
Edited by Technotools 2015-03-27 10:38 AM
|
|
|
|
Global Moderator H/PC Guru Posts: | 7,188 |
Location: | USA | Status: | |
| Now run execcheck on the mfcce300.dll and see what it is missing. Probably the olece300.dll...
BTW, the \windows folder is where you put all .dll (driver) files normally.
Also, usually it requires a warm reset to register the driver... |
|
|
|
Global Moderator H/PC Oracle Posts: | 12,671 |
Location: | Southern California | Status: | |
| WinamPAQ does require mfcce300.dll. But you have to make sure that it's the right version, as there's an H/PC 2000 version as well as a Pocket PC version. WinamPAQ also comes in both H/PC 2000 and Pocket PC versions, so you have to match versions of mfcce300.dll to the corresponding version of WinamPAQ. Which version are you using for each? (Also, it's perfectly fine to put the DLLs in the same folder with WinamPAQ, and probably a good idea in your case since your device dumps installed files from \Windows every time you reboot the device. )
Rich, running Executability Check on mfcce300.dll won't tell anything about olece300.dll. It's the application itself that may or may not require olece300.dll in addition to mfcce300.dll. |
|
|
|
H/PC Newbie Posts: | 5 |
Location: | Afghanistan | Status: | |
| UPDATE
Execheck says mfcce300 is an invalid file.
i Replaced it and now Execheck response is ok
if i do execheck on the winampaq executable file is ok.
But if i run winampaq.exe i have an error
"load dllfail"
the app open but i cannot load any file on the player. |
|
|
|
Global Moderator H/PC Guru Posts: | 7,188 |
Location: | USA | Status: | |
| Did you try the HPC2000 version or the Sig version? Both are ARM builds, but the Sig is for CE.NET. |
|
|
|
H/PC Newbie Posts: | 5 |
Location: | Afghanistan | Status: | |
| i cant find this version.
i actually use HPC2000 version.
what is "Sig" meaning? |
|
|
|
Global Moderator H/PC Guru Posts: | 7,188 |
Location: | USA | Status: | |
| This website's download area has versions for both HPC2000 and the Sigmarion III, which is a CE.NET 4.2 hardware device. That version is designed to work with the native drivers found in CE.NET 4.2. |
|
|
|
Global Moderator H/PC Oracle Posts: | 12,671 |
Location: | Southern California | Status: | |
| Slight correction, Rich: the Sigmarion III is a Windows CE .net 4.1 device. (That version should work fine in a CE 4.2 device, though; however, that version needs mfcce400.dll rather than mfcce300.dll. )
I got the same error when I tried the Pocket PC version on a CE 5 netbook - but the app still worked fine after I clicked OK on the error. I opened up an MP3 file and it played without a problem. |
|
|
|
H/PC Newbie Posts: | 5 |
Location: | Afghanistan | Status: | |
| i have to rename mfcce400 in mfcce300 to run winampaq. i have the same error. The app runs but no playback |
|
|
|
Global Moderator H/PC Guru Posts: | 7,188 |
Location: | USA | Status: | |
| Have you tried any of the other CE MP3 players we have posted here? |
|
|
|
Global Moderator H/PC Oracle Posts: | 12,671 |
Location: | Southern California | Status: | |
| Renaming mfcce400.dll to mfcce300.dll won't work - they're two different files. |
|
|